FITXA TÈCNICA / FITXA DE SEGURETAT Check in the cleaning section, for previous actions in the following restoration processes.
-
Ref. Sanitizing matte plastic paint for exterior and interior use. Thanks to the new silver ion technology, it is resistant to bacteria and fungi, protecting and cleaning the applied surfaces. Almost odorless and with highly decorative features, such as resistance to wet rubbing, covering and performance. Excellent results. Suitable for any construction support but thanks to its sanitizing nature, it is especially suitable for hospitals, residences, schools, hotels and homes in general. VOC <1 g / L - 2010 30 g / L.
SECURITY SHEET -
Ref. 15592 Flexible waterproofing mortar, for the coating of insulating plates. Without retraction. It can be armed with ARTIMIX 9 MESH to improve the mechanical resistance, the possible dilatations or the blows. It does not need water. It comes in two components powder and resin. Uniform finish and excellent leveling. Reduce the consumption of the coating or finishing paint. Its planimetry and softness of application allow finishes with finer and more aesthetic coatings than other mortars on the market.
-
Ref. 15591 Permanent adhesive mortar for all kinds of construction materials. Highly adhesive leveling paste for fixing and gluing the insulating plates in the Artictherm process. It comes in two components powder and resin. Once the mixture is made, it becomes a smooth paste that is easy to apply without detaching or retracting. Matt Gray finish.
-
Ref. 04024 Paint / coating similar to the ARTICRIL MILENNIUM, but with siloxane binders that give it a water-resistant and non-stick nature, keeping the supports dry and clean. Very matt finish. Especially indicated in the rehabilitation of facades in urban climates for its resistance to dirt. Very hard and easy to clean. Vertical waterproofing and protector of rain and humidity. Good breathability Long durability Protection of concrete, improves resistance to carbonation. Resistance to mold. High performance and high covering power. White and colors. VOC 22g / l - 2010 40g / l. UNE 48244 certification: 2007.
-
Ref. 07033
Waterproof coating with textured elastic acrylic binder. Multifunctional Anticarbonatation. Breathable Absorbs cracks up to 2 mm. It can be assembled with reticulated mesh. Great filling power and homogenization of very irregular surfaces. Thicknesses of 1 - 1.5 mm are achieved. Different rough finishes, chopped, gotelé, ... Composed with hollow mineral particles, with air at very low pressure, has a very low thermal and acoustic transmission power and a great power of isolation. It keeps the supports hot and dry giving comfort in the interiors. Is light. Convenient application. White and colors. VOC 4g / l - 2010 40g / l.
Anti-carbonation certificate according to UNE-EN 13295: 2005 and CE marking according to UNE-EN 1504-2: 2005.
DATA SHEET / SAFETY DATA SHEET / CERTIFICATION (Anti-Carbonation) / CERTIFICATION (CE Marking)
-
Ref. 07036 Smooth elastic waterproofing coating similar to ARTIGUM LISO, also with binder based on acrylic resins, but mixed with siloxanicas that give it a water-resistant and non-stick nature of the dirt, keeping the supports dry and clean. Very indicated in urban climates for its resistance to dirt. White and colors. COC 3g / l - 2010 140g / l. Certificate of anti-carbonation according to UNE-EN 13295: 2005 and CE marking according to UNE-EN 1504-2: 2005
DATA SHEET / SAFETY DATA SHEET -
Ref. 07034
Smooth elastic waterproof coating. With acrylic binder It contains hollow mineral particles and natural fibers, which reinforce its lightness. Waterproofing, decoration and insulation of facades and interiors. Its layer thickness and its elasticity allow to absorb microcracks up to 1 mm. It can be assembled with reticulated mesh. Uniformity of finishing, corrects deficiencies of the support. Anticarbonatation. Breathable No possibility of cracking when aging. High resistance to alkalinity, sunlight, high condensation and extreme climates. Mate. White and colors. VOC 3g / l - 2010 140g / l.
Anti-carbonation certificate according to UNE-EN 13295: 2005 and CE marking according to UNE-EN 1504-2: 2005.
DATA SHEET / SAFETY DATA SHEET / CERTIFICATION (Anti-Carbonation) / CERTIFICATION (CE Marking) -
Ref. 07031 Rough acrylic coating. With microlaminar extenders, which give it a high resistance to aging compared with other acrylics on the market. Aesthetic finish on exteriors and facades. Great filling power and homogenization of very irregular surfaces. Thicknesses of 1 - 1.5 mm are achieved. Vertical raincoat with good breathability. Different smooth finishes, rough, chopped, monolayer ... Resistant to mold. The good drying behavior allows an easy application. Work on consolidated and stable surfaces. White and colors VOC 4g / l - 2010 140g / l.
-
Ref. 07032 Acrylic coating. Smooth and stony finish. Ideal in public works with concrete formwork, on highways, ports, retaining walls, ships ... Vertical raincoat with good breathability. To fill the irregularities and coke of the supports. Resistant to mold. White and colors. VOC 5g / l - 2010 140g / l.
-
Ref. 07062 Flexible acrylic mortar to siloxane. Especially indicated for the waterproofing and decoration of facades. The projected application or trowel allows different textured finishes. The siloxane content gives it a waterproof and non-stick character. Easily covers microfusures. Ideal to regularize supports. Excellent resistance to weathering and good adhesion to concrete, mortar, fiber cement, etc... Breathable to water vapor and impermeable to rainwater. White and colors. COV 4g/l – 2010 140g/l.
-
Ref. 13055
Water based bicomponent sanitary epoxy paint. Interior pavements subjected to moderate abrasion. Anti-carbonation protection of concrete indoors. Decontaminable walls and walls. Easily washable It does not vitrify. Tenacious. Ideal to finish in EPOCRIL-3C processes on wet soils. With benefits similar to the other two-component in terms of adhesion and chemical and mechanical resistance, but being water-based, it does not smell when applied, which makes it indispensable for jobs in food industries, warehouses, medical centers, enclosures or poorly ventilated . Glossy finish. White, standard and colors. Low VOC 18g / l - 2010 140g / l.
Certification of reaction to fire of floor coverings according to UNE-EN ISO 11925-2: 2011 and UNE-EN ISO 9239-1: 2011 obtaining the classification CLASS BFL-S1, of reaction to the generic fire according to UNE-eN 13823: 2012 + A1: 2016 with classification CLASS B-S1, D0 of hardness (pendulum Persoz) according to UNE in ISO 1522, gloss according to UNE in ISO 2813, Taber abrasion according to ASTM D 4060, and CE marking according to UNE-eN 1504-2: 2005.
DATA SHEET / SAFETY DATA SHEET (A) / SAFETY DATA SHEET (B) / CERTIFICATION (reaction to fire) / CERTIFICATION (reaction to fire) / CERTIFICATION (hardness, gloss, abrasion) / CERTIFICATION (CE marking)
/ CERTIFICACIÓN (agua potable) -
Ref. 07022 Anti-painted and anti-posters. Not permanent For all types of porous surfaces. Dilutable with water Creates protective film that is removed with alkalized water and ammonia, under pressure. Graffiti is removed with soap and water. Maximum economy and effectiveness for urban maintenance in towns and cities. Always apply on clean and dry surfaces. Ecological. It can also act as a release agent for concrete in molds made of wood, cement, plaster, plastic. VOC 6g / l - 2010 30g / l.
-
Ref. 07041 Long lasting polysiloxane in aqueous base for facades and monuments. With great performance, resulting in a very thin layer integrated into the support. To obtain colored impregnations in porous materials. Completely waterproof, with a waterproof character, it respects the transpiration of materials, stone, concrete, lime ... It provides unification of the funds, preserving the original texture. No possibility of cracking when aging. Protector against carbonation. High resistance to alkalinity, fungi, sunlight, high condensation and aggressive environments in general. It prevents dust adhesion and is self-cleaning. Impeccable matte finish without splicing or reworking. It is produced to achieve opaque finishes or glazes. White and colors. VOC 4g / l - 2010 - 40g / l.
-
Ref. 13016
Water paint based on pliolite resins. Ideal for facades and interiors where you have to let the walls breathe and maintain an aesthetic finish. It is microporous, being highly breathable to water vapor. With water-resistant character. Resistance to atmospheric agents. Very good adhesion and integration to the supports. Car washable with rain. Resistance to mold and alkalinity. Very good cover and easy application. Prime on porous substrates with the consolidating fixative of NEW TEC FIJO nanoparticles, with deep penetration or with ARTISIL impregnation. Application without odors Permanent white, not yellow and colors. VOC 5- 2010 40g / l.
UNE-EN 1542 certificate (traction adhesion) and UNE-EN ISO 7783 (water vapor permeability)
-
Ref. 07132 Pleated paint based on acrylic resins cauchadas. Excellent coating for facades, with great resistance to aging, 15 years per layer even in extreme or aggressive climates, and without gaining thickness, facilitating tasks in future rehabilitation. Its particles in the different layers are interlinked, creating a microporous coating that allows the supports to breathe. Vertical waterproofing. Self-cleaning with rain water. Excellent adhesion and integration to the support. Resistance to mold and alkalinity. Protection against carbonation. It allows to apply in low temperatures. Ideal for priming with PLIOART IMPREGNACIÓN, with which you can mix to create glazes or intermediate layers. Respects the original textures a lot. White and totally uniform colors, without alterations in joints and recesses. VOC 428g / l - 2,010 430g / l.
-
Ref. 03063 Water-based polyurethane varnish for concrete, printed concrete, stone and wood. Sparkly. Flexible. Resistance to sunlight. Renovation of veneers, slate, natural and artificial stone, masonry .... Protection of dirt on elastomers such as ARTIGUM GEL FIX, does not present sticky touch or at high temperatures. On plastic paints to reinforce alkali resistance, moderate abrasion and pedestrian traffic. Highlight the appearance of the surfaces. Easy horizontal and vertical application. VOC 24g / l - 2010 130 g / l. The following products, unlike the previous ones, can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
-
Ref. 13035 Two-component glossy aliphatic polyurethane varnish. Exterior Interior. Excellent tenacity High chemical resistance, mechanical resistance and sunlight. Special for concrete floors, protection of absorbent marble, polyester resins (boats), wood in extreme environments. To protect ARTIMIX-20 MICROCEMENTO in workplaces and pavements. When high mechanical and chemical resistance is required. Available in satin and matt finish. On porous supports seal with a first coat of gloss. VOC 398g / l - 2,010 400 g / l. UNE-ENV 12633: 2003 Slip resistance. The following products, unlike the previous ones, can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
DATA SHEET / SAFETY DATA SHEET / SAFETY DATA SHEET (catalyst)
-
Ref. 13035 Water-based one-component varnish for the protection of floors and decoration of the ARTIMIX 20 micro cement or similar porous supports (stone, mortar, printed concrete, brick, wood ...). Indoor and outdoor use. Shiny finish. Excellent wetting and consolidation of the support, blocking possible efflorescence. It can be applied as the first coat of the BARTIDUR A2C to minimize the usual increase of tone of the varnishes to the solvent. Easy horizontal and vertical application. Resistance to moderate abrasion and pedestrian traffic. COV 50- 2010 140g / l. Can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
DATA SHEET / SAFETY DATA SHEET -
Ref. 06048 Water repellent and sealant for porous and absorbent surfaces. Excellent penetration Glossy finish. Compatible with alkaline and cementitious supports. Interior and exterior. It does not yellow. Avoid the adherence of dust and dirt. It is micro porous and allows the support to breathe. It prevents the formation of salts and the growth of fungi. Long-term treatment 3 g / l - 2010 30 g / l. Can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
-
Ref. 06132 Consolidating and water repellent impregnation varnish. Solvent base. Creates a film inferior to conventional varnishes. Very penetrating, hardens and seals any construction material. Special for exposed work, concrete and broken stone. When necessary a waterproof finish is not invisible. Increase the tone of the support. Apply only on porous surfaces. A layer allows satin finish, successive layers can increase it to bright. Accept pigmentation. Waterproof and breathable superficially to water vapor. VOC 672g / l - 2,010 750g / l. Can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
-
Ref. 06134 Hydrophobic consolidating impregnation for porous materials. Creates surface film integrated in the support. With high penetration, it seals the pores, hardening the dusty supports, brick, face, concrete, mortars, old lime stuccos ... Suitable for limestones, sandstones and granites. When necessary a waterproof finish is not invisible. Transparent finish with slight tone, which increases as successive layers are applied. Accepts pigmentation to make glazes. Waterproof and with superficial perspiration. 741 g / L - 2010 750 g / L Can create film and caution must be taken with wet supports or high salt content, since it can encapsulate them and being translucent finish they could be seen. On the other hand they protect, waterproof and reinforce the renewed aspect.
-
Ref. 06046 Water-repellent and water-repellent, based on fluorinated acrylic resins. It does not form a film. Destined to the protection of porous materials against the penetration of oils, fats, lubricants ... on surfaces such as tiles, reconstructed stones, marble, concrete, cement, natural stones, etc. Pearl effect. Without smell. It does not increase the tone of the support, it is invisible. VOC 10 g / L - 2.010 30g / L.
-
Ref. 06181 Consolidating and hydrophobic cortical impregnation in solvent base. To stop finishing, but can be repainted with solvent paints. For stones, concrete and stuccos. Great penetrating power. High values of resistance to diffusion for a better protection against carbonation and a lower resistance to diffusion of water vapor, breathable. Saturate until homogenization of the support. Apply from the bottom up. Wet layer on wet. Colorless, slightly increases the tone of the support, without filmifying. VOC 742g / l - 2,010 750g / l.
-
Ref. 06042 Siloxane water repellent with water-based nanoparticles for mineral supports. Excellent penetration Invisible. It does not film and does not modify the appearance of the support. Microporous, waterproof and transpires water vapor. Self-cleaning, keeps the surface clean and free of dust and dirt. Avoid the formation of salts. Resistant to mold. Ideal for facades of exposed work stuccos, fiber cement, natural stone, etc. In the application on paints and coatings to water or solvent, reinforces the hydrophobic performance. VOC 1- 2010 30g / l.
-
Ref. 06141 Water repellent based on modified polysiloxanes. Long duration, over 10 years. Invisible, it does not modify the background tone. For exposed work, bricks, stone, stuccos ... in any climate. Also for textiles, wood and non-cracked porous materials. Microporous, does not form superficial film. Great water-repellent capacity and high perspiration. Resistant to mold. It prevents the formation of salts and does not green with time. Self-cleaning, keeps the surface clean, hindering the adherence of dust and dirt. Do not dilute, apply to saturation in two layers from bottom to top crossed wet on wet. The immersion treatment is also possible. VOC 748g / l - 2,010 750g / l.
-
Ref. 10592 Continuous powder coating on the basis of high performance hydraulic micro cement. Based on calcium cements and marble powder of different granulometries, it is presented in two modes FINE and THICK. It is used for the realization of highly decorative continuous coatings, both vertical and horizontal. Direct adherence on any type of material. Very hard and tenacious. Apply ARTIPUR SELLADOR as a primer and between layers, it will provide a better homogenization of the absorptions, and in supports with different materials (tiling, ceramics ...) a better regularization. It is advisable to seal with NEW TEC BARNIZ varnish or on floors or in continuous immersion BARTIDUR A-2C. Low thermal diffusion Antistatic Kitchens, toilets, workshops, restaurants, hotels, shops ... interior and exterior decorations. White color. Easily colorable.
-
Ref. 10095 Liquid mixing and kneading. To color the MIX 5 homogeneously. It avoids color differences in the dyeing and during setting. Reproducible colors With pigments resistant to alkalinity. Tinting of monolayers. Check colors VOC 1g / l - 2010 30g / l.
-
Ref. 10596 Mixed air lime mortar with special aggregates and modifying additives. To cover new facades or for the rehabilitation of old ones. Textured finish. Concrete repair High resistance and stability to acid rain and pollution in urban environments and the demands of extreme climates. Repair of structures and load walls in poor condition when thickness and strength are required. No retractions. Thick layer: 20 mm. You can get a wide variety of classic stucco finishes, present in our facades and with easy application. Working layers of different colors and with traditional tools you get beautiful sgraffito. It can be finished with a wide variety of coatings, consolidants and / or water repellents. Dilution approx 25 Kg + 7 liters (1 part ARTICRIL RESIN 6 + 3/4 parts of water). It is advisable to prime the support and between layers with the same mixture. White color. It can be diluted with ARTIMIX 5 BASE to color, see colors. On request, production of dry-colored mortar in the factory.
-
Ref. 10094 Liquid mixing and kneading. To color the MIX 4 evenly. It avoids color differences in the dyeing and during setting. Reproducible colors With pigments resistant to alkalinity. Tinting of monolayers. Check colors VOC 1g / l - 2010 30g / l.
-
Ref. 10594 Cellular restoration mortar. Recovery and creation of volumes. Very light. Composed in its interior with hollow natural mineral particles, which crystallize in their interior the salts and caleos of the supports, gaining hardness with the years. No cracking or shrinkage at temperatures from -15oC to + 80oC. Extraordinary resistance to slow compression of buildings. Ideal for rehabilitation work and creation of new environments and interior and exterior decorations. Its touch and finish are natural. Its drying is very controlled, allowing a huge variety of work techniques. Repair and creation of stones and stuccos, chairs, graffiti, exposed work, ... It is sculptable and moldable. You can work in molds. Product of unbeatable specific qualities, is present in many renovations and restorations of facades and monuments around the world. Fronts of balconies, edges, moldings, screeds ... It weighs less and works better than other recommended mortars. Used in archeology to redo volumes in findings of stones, ceramics ... in pitchers, walls, houses ... Desalination of ancient walls in monumental restoration. It can be used in thinner and diluted layers, even by brush, roller or platen. It admits aggregates to equalize textures. It is advisable to waterproof with HIDROFUART BIO or NEW TEC HIDROFUART W, or protect with ARTISIL mineral coating, or with other breathable paints. Color Gray, is also available in White ARTIMIX 4-BL 10595. Dilution approx 15 Kg + 8 liters (1 part ARTICRIL RESIN 6 + 3 parts of water). It is advisable to prime the support and between layers with the same mixture. It can be diluted with BASE ARTIMIX 4 to color. Check colors Upon request, production of dry-colored mortar, in the factory.
-
Ref. 10032 Resin in aqueous dispersion for connecting bridges between concretes or mortars. Adhesive of insulating materials, plasterboard, partitions, pillars, textiles, polystyrene, etc ... For indoor and outdoor protected applications, vertical and horizontal. With delayed crosslinking, it allows to maintain the adhesion 3-4 days of its application. It does not lose benefits even at 0ºC. Compatible with supports with residual moisture, it is permeable to water vapor. Do not apply as a final layer of protection. VOC 1g / l - 2010 30g / l.
-
Ref. 10031 Reactive polyvalent resin in high concentration aqueous solution. Hydraulic mortar improver, acts as an elasticizer, avoiding its tendency to crack and the formation of fissures. Plasticizes the mortars, avoiding retractions, improving fluidization in them and providing them with greater resistance to compression and abrasion. Bridge of union between old and new mortars, stuccos or mortars, improving their adherence. Sprinkle with cement between coats ... Dilution 1/3 water. VOC 1g / l - 2010 30g / l.
DATA SHEET / SAFETY DATA SHEET -
Ref. 06164 Polyurethane fixative for disintegrated supports. Great hardness and tenacity. Recommended for dry, wet or dusty concretes. Consolidates and protects concrete pavements. Sealing layer in porous floors before applying the ARTIDUR-X 100 or ARTIDUR A2C finishing polyurethanes. Outdoors or exposure to sunlight do not use as a visible layer, yellow. It can be seen in places protected from sunlight, increasing the tone of the concrete. Apply in well-ventilated places. Restoration of exterior wood very aged, saturate before painting. VOC 550g / l - 2010 750g / l.
-
Ref. 07321 Transparent and waterproof elastomeric coating. Indicated for the repair, protection and waterproofing of facades and roofs with glazed finishes, tiles and tiles, as well as stones and slate, where a transparent finish is necessary. Sealing of sanitary ceramics eliminating joints and protecting from detachment. On ceramic supports, clean and tone with STONEART. It can be reinforced by arming with the fiberglass ARTIMAT FIX mesh that is completely absorbed, transparent and that unifies splices and overlaps. To prevent adhesion of the external dirt, varnish with BARTICRIL PUR. It can also be repainted with a variety of opaque finishes. It is also an excellent consolidant and protector of concrete. 03063. VOC 7g / l - 2010 140g / l.
-
Ref. 08063 Capa segelladora sobre superfícies poroses, absorbents o irregulars. S’aplica com a preparació del PROCÉS ARTIPUR, tant en acabats en color com transparent. Evita micro fissures o petits esquarteraments homogeneïtzant l’absorció entre les juntes en els enrajolats, facilitant la formació de la pel·lícula elàstica amb els elastòmers ARTIPUR. En qualsevol suport i circumstància, per assegurar un bon ancoratge, es recomanable afegir un 1% d’ADITOR PU promotor d’adherència . COV 28g/l - 2010 30g/l
FITXA TÈCNICA / FULLA SEGURETAT
